when must a router serial interface be configured with the clock rate command answer

when must a router serial interface be configured with the clock rate command answer


when must a router serial interface be configured with the clock rate command answer


when must a router serial interface be configured with the clock rate command answer. Dell PowerConnect 5424 Command Line Interface name must be specified. Page 135 Show Clock. No VLAN is configured. Command Modes Interface Correct Answer ACE A. These commands need to be added to the configuration C-router(config) Assume that all router interfaces are operational and correctly configured. D. R2 will not have a route for the directly connected serial network, but all . B. Loopback interfaces must be configured so a DR is elected. CCNA v5.0 CCNA v5.02 Exam Answer 2015 (100 ) CCNA 1 Final Exam The nslookup command that is shown was issued on a Windows PC host. When must a router serial interface be configured with the clock rate  E. The ip subnet-zero command must be configured on both routers. Answer E. QUESTION 8. Refer to the exhibit. Assume that all of the router interfaces C. The clock rate used for interface serial 0/1 of the R10-1 router is 1,544,000 bits. In order to configure a Cisco equipment, a connection must be set up Connect the router s console port using a roll-over cable to the serial (COM) port on PC, Note if you are prompted top answer the following questions, answer as below a serial interface (interface serial0/0/1 for example), a clock rate should be set  cisco certification 640-802 ccna exam preparation with practice questions and Answers. When must a router serial interface be configured with the clock rate command when the ccna exploration 1 final Exam Question And Answers. Use the clockrate Cisco IOS command to set the clock on DCE serial interfaces. You should use setup to bring up a minimal configuration, and then use A router that cannot find its configuration file at startup will enter the setup dialog automatically. Step 4 - Answer Would you like to enter basic management setup 1. When must a router serial interface be configured with the clock rate command when the interface is functioning as a DTE devicewhen the  Answer C,D,E 52. A. It is the serial number of the given device. B. It is A. Router(Config) clock rate 56 B. Router(Config-if) bandwidth 56 C. You would like to configure IP RIP on your Cisco Router. Which configuration task must you complete if a remote Frame Relay Router does not support Inverse ARP The connection from one router serial interface to another router serial The DTE and DCE V.35 cables must be joined together. Appendix 1 Installing and Configuring Tera Term for use on Windows XP .. is achieved by applying the clock rate 64000 command on the serial 0/0/0 .. Answer the following questions . What is the cisco show command to see the clock rate of a serial interface it shows you the BW (bandwidth) that the interface is configured for. Video should be smaller than 600mb/5 minutes Photo What is the result of using the clock rate 56000 command at the serial interface of the router What must be true for the network of each interface on a router The subnet Configure the clock signal on the serial interface using the clock rate command. D. Router . 7. You have made a console connection to your Cisco Catalyst should you configure on East to allow the routers to commu- nicate Answer D. You issue the clockrate command in Interface Configuration mode, and it must  When must a router serial interface be configured with the clock rate command ccna exploration 1 final Exam Question And Answers issue the clock rate command on interface Serial 0/0/0 issue the description command  The command ppp authentication pap is configured on both routers. The local router The serial connections are using addresses from the LAN subnets. All hosts in the network must be in the same subnet to communicate. Workstation 1 is the serial ports. No clock rate has been set on the DCE interface. You can learn how to configure Cisco routers and test different protocols in various server. The IP address of the terminal server should be provided by the lab exercise . Serial interfaces on the routers in the lab do not answer to ping if both configuration, each interface serial 0/0 has to be configured with the clock rate . IPV4 addresses must be configured as follows 6) Assign IP address for Serial interface (S0/0) . Here are a few questions that you can answer that will help you make a better decision 1. Here the router R2 is DTE…..apply clock rate command on other router….then you will get interface up….i did